Prices

  • Houly Rate……..60.00
  • Mill / Lathe Houly Rate…..80.00
  • Clean & Oil Basic…….35.00
  • Clean & Oil: Complete Disassembly Inspection of Parts……….60.00

Refinishing

  • HOT BLUE (Oxynate 7)
  • Abrasive / Bead Blast (Matte) Finish…..145.00
  • 240 Grit (Satin) Finish……Handgun….165.00 / Long Gun……175.00
  • 400 Grit (Gloss) Finish….Handgun…185.00 / Long Gun….195.00
  • 500 Grit + 555 (High Polish) Finish….Handgun…….225.00 / Long Gun…..275.00
  • Parkerizing……170.00
  • RUST BLUE
  • Long Guns……300.00
  • Barrels….150.00
  • Frame…..100.00
  • Abrasive / Bead Blast Stainless Steel…..100.00
  • Nitre Blue / Small Parts…..75.00
  • Jewell Bolt…..75.00
  • Cerakote…….Long Guns….180.00……Handguns…..160.00

Sight Work

  • Drill-Tap per hole……20.00
  • Cut dovetail…..60.00
  • Install sight insert….30.00
  • Install shotgun bead….25.00
  • Mount scope…..30.00

General Barrel, Action and Rifle Work

  • Thread Barrel for Muzzle Device……100.00
  • Install Badger Bolt Handle……65.00
  • Check Headspace……35.00
  • Make Chamber Casting…..50.00
  • Install Barrel Liner……..125.00 (not including liner)
  • Cut & Crown Barrel…..60.00
  • Thread-Chamber-Fit Barrel to Action……225.00 (not including barrel)
  • Install Pre-threaded Chambered Barrel…….125.00
  • Blueprint Remington or Similar Action…….250.00
  • Add Blueprint to Barrel Blank install…….125.00
  • Forge Bolt Handle…..75.00
  • Weld on New Bolt Handle…….125.00
  • Install Safety……50.00
  • Trigger Work (install-adjust)……50.00

Shotgun Work

  • Long Forcing Cone……..70.00
  • Resolder Rib……..225.00
  • Resolder Forend Lug…….100.00
  • Straighten/Adjust Barrel (point of impact)………65.00
  • Polish Chamber/Bore ………50.00
  • Open/Modify Choke……..65.00
  • Install Screw in Choke……..125.00
  • Raise Dent in Barrel………50.00

Stock Work

  • Hunter Finish on average stock…………150.00
  • Filled and rubbed finish on average stock……………..190.00
  • Glass bed action…..85.00
  • Glass bed barrel and action……..100.00
  • Install recoil pad – labor only……50.00
  • Install sling swivels……..35.00
  • Install stock cross bolt……45.00
  • Inlet and finish semi-inletted stock – (unfilled)……200.00 – (filled)….240.00

Handgun Work

  • Chamfer Revolver barrel (forcing cone)………45.00
  • Chamfer Revolver cylinder…..60.00
  • Revolver Action Job (replacement parts not included)…..75.00
  • Rebarrel Revolver (factory barrel, labor only)….100.00
  • Straighten crane on Revolver……..45.00
  • Bob Hammer……50.00
  • Semi-Auto Action Job (replacement parts not included)…..120.00
  • Install 1911 Thumb Safety…….50.00

AR-15 Work

  • Install Aftermarket Trigger………50.00
  • Install Aftermarket Forend / Free Float……50.00
  • Assemble complete upper……..55.00
  • Assemble complete lower…….55.00
  • Assemble complete Rifle……100.00
  • Install / replace gas block….40.00
  • Install / replace barrel……..60.00
  • Install / replace buttstock and buffer tube….30.00
  • Pin & Weld muzzle brake / Flash Hider……50.00
  • Thread Barrel for muzzle device…….100.00